Frictional Characteristics of EN AW-6082 Aluminium Alloy Sheets Used in Metal Forming
PDF

Keywords

EN AW-6082-T6
friction
sheet metal forming
strip drawing test

How to Cite

Slota, J., Kaščák, Ľuboš, & Lăzărescu, L. (2024). Frictional Characteristics of EN AW-6082 Aluminium Alloy Sheets Used in Metal Forming. Advances in Mechanical and Materials Engineering, 41(1), 79-87. https://doi.org/10.7862/rm.2024.8

Abstract

This article is devoted to testing EN AW-6082 aluminium alloy sheets in friction pair with NC6 (1.2063) tool steel. A special tribometer designed to simulate the friction conditions in sheet metal forming processes was used for friction testing. The research aimed to determine the influence of contact pressure, surface roughness of the tool, and lubrication conditions on the value of the coefficient of friction in the strip drawing test. Three grades of typical petroleum-based lubricants with kinematic viscosities between 21.9 and 97 mm2/s were used in the tests. The surface morphologies of the sheet metal after the friction process were observed using a scanning electron microscope. A tendency for the coefficient of friction to decrease with increasing contact pressure was observed. LHL32 and 75W-85 oils lost their lubricating properties at a certain pressure value and with further increase in pressure, the coefficient of friction value tended to increase. The 10W-40 oil with the highest viscosity reduced the coefficient of friction more intensively than the LHL32 oil.

https://doi.org/10.7862/rm.2024.8
PDF

References

-6082-T6 Aluminum. (2023, January 10) https://www.makeitfrom.com/material-properties/6082-T6-Aluminum

Aiman, Y., & Syahrullail, S. (2020, July 13). Ring compression test of aluminum alloy AA6061 using palm mid olein as a metal forming lubricant. Proceedings of Mechanical Engineering Research Day MERD’22, (pp. 272-276). UTeM Press.

Bay, N., Olsson, D. D., & Andreasen J. L. (2008). Lubricant test methods for sheet metal forming. Tribology International, 41(9-10), 844–853. https://doi.org/10.1016/j.triboint.2007.11.017

Bellini, C., Giuliano, G., & Sorrentino, L. (2019). Friction influence on the AA6060 aluminium alloy formability. Frattura ed Integrità Strutturale, 49, 791–799. http://dx.doi.org/10.3221/IGF-ESIS.49.70

Chruściński, M., Wielowiejska-Giertuga, A., Garbiec, D., Rubach, R., & Ziółkiewicz, S. (2017). Badania tribologiczne materiałów przeznaczonych na elementy łożysk tocznych. Obróbka Plastyczna Metali, 4, 239–250.

Domitner, J., Silvayeh, Z., Sabet, A. S., Öksüz, K. I., Pelcastre, L., & Hardell, J. (2021). Characterization of wear and friction between tool steel and aluminum alloys in sheet forming at room temperature. Journal of Manufacturing Processes, 64, 774–784. https://doi.org/10.1016/j.jmapro.2021.02.007

Dou, S., & Xia, J. (2019). Analysis of sheet metal forming (stamping process): A study of the variable friction coefficient on 5052 aluminum alloy. Metals, 9(8), Article 853. https://doi.org/10.3390/met9080853

Dubey, R., Jayagantham, R., Ruan, D., Gupta, N. K., Jones, N., & Velmurugan R. (2023). Energy absorption and dynamic behaviour of 6xxx series aluminium alloys: A review. International Journal of Impact Engineering, 172, Article 104397. https://doi.org/10.1016/j.ijimpeng.2022.104397

Dubois, A., Filali, O., & Dubar, L. (2024). Effect of roughness, contact pressure and lubrication on the onset of galling of the 6082 aluminium alloy in cold forming, a numerical approach. Wear, 536-537, 205179. https://doi.org/10.1016/j.wear.2023.205179

Graba, M. (2020). Characteristics of selected measures of stress triaxiality near the crack tip for 145Cr6 steel - 3D issues for stationary cracks. Open Engineering, 10(1), 571–585. https://doi.org/10.1515/eng-2020-0042

Haar, R. (1996). Friction in sheet metal forming, the influence of (local) contact conditions and deformation [Doctoral dissertation, Universiteit Twente]. Universiteit Twente Repository. https://ris.utwente.nl/ws/portalfiles/portal/6079817/thesis_R_ter_Haar.pdf

Hol, J., Wiebenga, J. H., & Carleer, B. (2017). Friction and lubrication modelling in sheet metal forming: Influence of lubrication amount, tool roughness and sheet coating on product quality. Journal of Physics: Conference Series, 896, Article 012026. https://doi.org/10.1088/1742-6596/896/1/012026

Hu, Y., Zheng, Y., Politis, D. J., Masen, M. A., Cui, J., & Wang L. (2019). Development of an interactive friction model to predict aluminum transfer in a pin-on-disc sliding system. Tribology International, 130, 216–228. https://doi.org/10.1016/j.triboint.2018.08.034

Jewvattanarak, P., Mahayotsanun, N., Mahabunphachai, S., Ngernbamrung, S., & Dohda, K. (2016). Tribological effects of chlorine-free lubricant in strip drawing of advanced high strength steel. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 230(8), 974–982. https://doi.org/10.1177/1350650115622366

Kaščák, Ľ., Cmorej, D., Spišák, E., & Slota, J. (2021). Joining the high-strength steel sheets used in car body production. Advances in Science and Technology Research Journal, 15(1), 184–196. https://doi.org/10.12913/22998624/131739

Lachmayer, R., Behrens, B. A., Ehlers, T., Müller, P., Althaus, P., Oel, M., Farahmand, E., Gembarski, P. C., Wester, H., & Hübner, S. (2022). Process-integrated lubrication in sheet metal forming. Journal of Manufacturing and Materials Processing, 6(5), Article 121. https://doi.org/10.3390/jmmp6050121

Ludwig, M., Müller, C., & Groche, P. (2010). Simulation of dynamic lubricant effects in sheet metal forming processes. Key Engineering Materials, 438, 171–178. https://doi.org/10.4028/www.scientific.net/KEM.438.171

Luiz, V. D., Santos, A. J. D., Câmara, M. A., & Rodrigues, P. C. D. M. (2023). Influence of different contact conditions on friction properties of AISI 430 steel sheet with deep drawing quality. Coatings, 13(4), Article 771. https://doi.org/10.3390/coatings13040771

Lukovic, M. (2019). The influence of surface temperature on the coefficient of static friction. The Physics Teacher, 57, 636–638. https://doi.org/10.1119/1.5135798

Meiler, M., Pfestorf, M., Geiger, M., & Merklein, M. (2003). The use of dry film lubricants in aluminum sheet metal forming. Wear, 255(7-12), 1455–1462. https://doi.org/10.1016/S0043-1648(03)00087-5

Mohamed, M., Farouk, M., Elsayed, A., Shazly, M., & Hezagy, A. (2017). An investigation of friction effect on formability of AA 6061-T4 sheet during cold forming condition. AIP Conference Proceedings, 1896, Article 080025. https://doi.org/10.1063/1.5008105

Mukhopadhyay, P. (2012). Alloy designation, processing, and use of AA6xxxx series aluminium alloys. International Scholarly Research Notices, 2012, Article 165082. https://doi.org/10.5402/2012/165082

Mulidrán, P.; Spišák, E.; Tomáš, M.; Majerníková, J.; Bidulská, J.; & Bidulský, R. (2023). Impact of blank holding force and friction on springback and its prediction of a hat-shaped part made of dual-phase steel. Materials, 16(2), Article 811. https://doi.org/10.3390/ma16020811

Nasake, T., & Sakuragi, K. (2017). Surface treatment of aluminium alloy for tribological applications. KYB Technical Review, 55, 18–24.

Onuseit, V., Umlauf, G., Reichle, P., Barz, J. P., Tovar, G., & Hirth, T. (2020). Tribological system for cold sheet metal forming based on volatile lubricants and laser structured surfaces. Dry Metal Forming Open Access Journal, 6, 128–165. https://doi.org/10.26092/elib/156

Reddy, I. S., & Vadivuchezhian, K. (2020). Sliding of various ductile materials (Al 6061, Al 6082) using pin on disc setup. Materials Today: Proceedings, 27, 2688–2692. https://doi.org/10.1016/j.matpr.2019.11.248

Reichardt, G., Wörz, C., Singer, M., Liewald, M., Henn, M., Förster, D. J., Zahedi, E., Boley, S., Feuer, A., Onuseit, V., Weber, R., Graf, T., Umlauf, G., Reichle, P., Barz, J.P., Tovar, G., & Hirth, T. (2020). Tribological system for cold sheet metal forming based on volatile lubricants and laser structured surfaces. Dry Metal Forming Open Access Journal, 6, 128-165. https://doi.org/10.26092/elib/156

Sabet, A. S., Domitner, J., Öksüz, K. I., Hodžić, E., Torres, H., Ripol, M. R., & Sammitsch, C. (2021). Tribological investigations on aluminum alloys at different contact conditions for simulation of deep drawing processes. Journal of Manufacturing Processes, 68, 546–557. https://doi.org/10.1016/j.jmapro.2021.05.050

Slota, J., Šiser, M. & Dvorák, M. (2017). Experimental and numerical analysis of springback behavior of aluminum alloys. Strength of Materials, 49, 565–574. https://doi.org/10.1007/s11223-017-9900-6

Tan, J. L., & Liew, K. W. (2023). Tribological behaviour and microstructure of an aluminium alloy-based g-SiC hybrid surface composite produced by FSP. Lubricants, 11(3), Article 124. https://doi.org/10.3390/lubricants11030124

Xia, J., Zhao, J., & Dou, S. (2022). Friction characteristics analysis of symmetric aluminum alloy parts in warm forming process. Symmetry, 14(1), Article 166. https://doi.org/10.3390/sym14010166

Xu, W., Gao, X., Zhang, B., Yang, L., Du, C., Zhou, D., Rawya, B., & Szymanski, M. (2018). Study on frictional behavior of AA 6XXX with three lube conditions in sheet metal forming. SAE Technical Paper, 2018-01–0810. https://doi.org/10.4271/2018-01-0810