Keywords
How to Cite
Abstract
The paper presents results obtained by SiC ceramic implementation for slide burnishing. Analyzes of the effect of the burnishing force and feed on selected surface texture parameters were conducted. The influence of technological parameters was assessed according to the analysis of variance. The burnishing force and feed affected most of the examined surface texture parameters in the analyzed ranges. Optimal values were found for the technological parameters. In most cases, the minimum of height parameters were achieved for 80 N of burnishing force and 0,063 mm/rev of feed. Limitations in the increase in the burnishing force were also found.
This is an Open Access article distributed under the terms of the Creative Commons Attribution License CC BY 4.0 (https://creativecommons.org/licenses/by/4.0/)
References
Bulikowska B., Gałda L. 2015. “The effect of surface roughness on the tribological properties of sliding elements in material assembly SiC-42CrMo4”. TRIBOLOGIA, XLVI(4): 21-31.
Dobrzański A. L. 2008. Non-metallic engineering materials. Gliwice: Publishing house of Silesian University of Technology.
El-Tayeb N.S.M., Low K.O., Brevern P.V. 2009. “On the surface and tribological characteristics of burnished cylindrical Al-6061”. Tribology International 42: 320-326.
Gałda L. 2014. Slide burnishing with ceramic material. In Contemporary problems in the technology of burnishing, 143-154. Publishing house of Gdańsk University of Technology.
Gałda L. 2016. “Selected factors effecting on wear resistance of sliding pairs”. BUSES – technology, operations, transport systems 17: 861-865.
Jaworska L., Sobierski L., Twardowska A., Królicka D. 2005. „Preparation of materials based on Ti-Si-C system using high temperature-high pressure method”. Journal of Materials Processing Technology 162-163: 184-189.
Jaworska L., Szutkowska M., Morgiel M., Sobierski L., Lis J. 2001. „Ti3SiC2 as a bonding phase in diamond composites”. Journal of Materials Science Letters 20: 1783-1786.
Jianxin D., Lili L., Mingwei D. 2007. „Erosion wear behaviours of SiC/(W,Ti)C laminated ceramic nozzles in dry sand blasting processes”. Materials Science & Engineering A 444: 120-129.
Konefał K., Korzyński M., Byczkowska Z., Korzyńska K. 2013. „Improved corrosion resistance of stainless steel X6CrNiMoTi17-12-2 by slide diamond burnishing”. Journal of Materials Processing Technology 213: 1997-2004.
Korzyński M. 2009. “A model of smoothing slide ballburnishing and an analysis of the parameter interaction”. Journal of Materials Processing Technology 209: 625-633.
Korzyński M. 2013. Experiment design. Warszawa: Scientific publishing house PWN.
Korzyński M., Lubas J., Świrad S., Dudek K. 2011. „Surface layer characteristics due to sidle diamond burnishing with a cylindrical-ended tool”. Journal of Materials Processing Technology 211: 84-94.
Liu S., Zeng Y.-P., Jiang D. 2009. “Fabrication and characterization of cordierite-bonded porous SiC ceramics”. Ceramics International 35: 597-602.
Przybylski W. 1987. Burnishing technology. Warszawa: Science Publishing House.
Radziejewska J., Skrzypek S.J. 2009. „Microstructure and residual stresses in surface layer of simultaneously laser alloyed and burnished steel”. Journal of Materials Processing Technology 209: 2047-2056.
Srivastava M., Grips V.K.W., Rajam K.S. 2008. “Influence of SiC, Si3N4 and Al2O3 particles on the structure and properties of electrodeposited Ni”. Materials Letters 62: 3487-3489.
Świrad S. 2011. “The surface texture analysis after sliding burnishing with cylindrical elements”. Wear 271: 576-581.
Yang J., Ma R., Zhu M., Xiong Y., Shi J., Li X., Li H., Che J. 2022. “Microstructure and mechanical properties of hot-pressed SiC nanofiber reinforced SiC composites”. Ceramics International (available online).
https://www.ceramit.pl/uploads/PDFy/w%C5%82asno%C5%9Bci_materia%C5%82%C3%B3w_ceramicznych. pdf (28th Feb. 2022)